Eaton WCL3225-470-R 47 uH Inductor, 140 mA Rated
Eaton WCL3225-470-R 47 uH Inductor, 140 mA Rated

Eaton WCL3225-470-R 47 uH Inductor, 140 mA Rated

Share
WCL3225-470-R: wire wound chip inductor, 47 uH ±5%, Q 10 at 2.52 MHz, 140 mA rated, DCR 5200 mOhm.
    • Product Details
    • Download

    Eaton WCL3225-470-R 47 uH Inductor, 140 mA Rated

    WCL3225-470-R at a glance: wire wound chip inductor, 47 uH ±5%, Q 10 at 2.52 MHz, 140 mA rated, DCR 5200 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberWCL3225-470-R
    OCL47 uH ±5%
    Q minimum @ test frequency10 @ 2.52 MHz
    SRF minimum10 MHz
    DCR maximum @ +25 °C5200 mOhm
    Rated current (20 °C rise)140 mA
    OCL test frequency2.52 MHz
    OCL test voltage500 mV
    Package3.5 x 2.9 mm, 2.25 mm high
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10931

    Outline Drawing

    WCL3225-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10931: outline views
    with rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 140 mA rating the winding drops about 728 mV and dissipates 102 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 10 at 2.52 MHz with self-resonance at 10 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCL3225 family this is value 26 of 39, in a range from 0.12 to 560 uH.

    Where This Series Fits

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: industrial connectivity (iot); computing/gaming consoles; smart meters; industrial equipment; machine-to-machine (m2m).
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products