Eaton WCLA1005V1-2R5-R 2.5 nH Wire Wound Chip Inductor
Eaton WCLA1005V1-2R5-R 2.5 nH Wire Wound Chip Inductor

Eaton WCLA1005V1-2R5-R 2.5 nH Wire Wound Chip Inductor

Share
WCLA1005V1-2R5-R: wire wound chip inductor, 2.5 nH ±10%, Q 15 at 250 MHz, 640 mA rated, DCR 120 mOhm.
    • Product Details
    • Download

    Eaton WCLA1005V1-2R5-R 2.5 nH Wire Wound Chip Inductor

    WCLA1005V1-2R5-R at a glance: wire wound chip inductor, 2.5 nH ±10%, Q 15 at 250 MHz, 640 mA rated, DCR 120 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberWCLA1005V1-2R5-R
    OCL2.5 nH ±10%
    Q minimum @ test frequency15 @ 250 MHz
    SRF minimum6000 MHz
    DCR maximum @ +25 °C120 mOhm
    Rated current (20 °C rise)640 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.19 x 0.66 mm, 0.60 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10981

    Mechanical Drawing

    WCLA1005V1-2R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10981: outline views
    with rated mm dimensions, pad layout and marking.

    How to Read These Ratings

    A wire wound chip inductor is a coil wound on a ceramic or ferrite core with metal end terminals, in a body the size of a resistor. Compared with a multilayer chip of the same size it gives a higher Q and a tighter tolerance, which is why it appears in filters and matching networks rather than only in supply decoupling.

    At the 640 mA rating the winding drops about 76.8 mV and dissipates 49.2 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 15 at 250 MHz with self-resonance at 6000 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1005V1 family this is value 8 of 52, in a range from 1 to 120 nH.

    Series Positioning

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Is the automotive version electrically different?
    The construction is the same; the qualification and the temperature range are not. The WCLA parts are AEC-Q200 qualified and rated to +125 °C, the commercial WCL parts to +85 °C.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Is the automotive version electrically different?
    The construction is the same; the qualification and the temperature range are not. The WCLA parts are AEC-Q200 qualified and rated to +125 °C, the commercial WCL parts to +85 °C.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message