Eaton WCLA1608V1-1R6-R 1.6 nH Inductor, 700 mA Rated
Eaton WCLA1608V1-1R6-R 1.6 nH Inductor, 700 mA Rated

Eaton WCLA1608V1-1R6-R 1.6 nH Inductor, 700 mA Rated

Share
WCLA1608V1-1R6-R: wire wound chip inductor, 1.6 nH ±10%, Q 18 at 250 MHz, 700 mA rated, DCR 40 mOhm.
    • Product Details
    • Download

    Eaton WCLA1608V1-1R6-R 1.6 nH Inductor, 700 mA Rated

    WCLA1608V1-1R6-R at a glance: wire wound chip inductor, 1.6 nH ±10%, Q 18 at 250 MHz, 700 mA rated, DCR 40 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberWCLA1608V1-1R6-R
    OCL1.6 nH ±10%
    Q minimum @ test frequency18 @ 250 MHz
    SRF minimum12500 MHz
    DCR maximum @ +25 °C40 mOhm
    Rated current (20 °C rise)700 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.78 x 1.10 mm, 0.95 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10982

    Dimensions and Pad Layout

    WCLA1608V1-1R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10982: outline views
    with rated mm dimensions, pad layout and marking.

    The Figures Explained

    Ceramic-core wire wound parts hold their value well with DC bias because there is no magnetic material to saturate. Ferrite-core versions give more inductance per size but start to roll off as the bias current rises.

    At the 700 mA rating the winding drops about 28 mV and dissipates 19.6 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 18 at 250 MHz with self-resonance at 12500 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1608V1 family this is value 1 of 31, in a range from 1.6 to 470 nH.

    Where This Series Fits

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Why choose wire wound over multilayer?
    Q. A wound coil has lower resistance for the same inductance, so Q is higher and the loss in a filter or matching network is lower. The price is size and cost, which is why multilayer parts dominate pure decoupling.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products