Eaton WCLA1608V1-270-R 27 nH RF Chip Inductor, SRF 2800 MHz
Eaton WCLA1608V1-270-R 27 nH RF Chip Inductor, SRF 2800 MHz

Eaton WCLA1608V1-270-R 27 nH RF Chip Inductor, SRF 2800 MHz

Share
WCLA1608V1-270-R: wire wound chip inductor, 27 nH ±5%, Q 36 at 250 MHz, 600 mA rated, DCR 220 mOhm.
    • Product Details
    • Download

    Eaton WCLA1608V1-270-R 27 nH RF Chip Inductor, SRF 2800 MHz

    WCLA1608V1-270-R at a glance: wire wound chip inductor, 27 nH ±5%, Q 36 at 250 MHz, 600 mA rated, DCR 220 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA1608V1-270-R
    OCL27 nH ±5%
    Q minimum @ test frequency36 @ 250 MHz
    SRF minimum2800 MHz
    DCR maximum @ +25 °C220 mOhm
    Rated current (20 °C rise)600 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.78 x 1.10 mm, 0.95 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10982

    Dimensions and Pad Layout

    WCLA1608V1-270-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10982: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 600 mA rating the winding drops about 132 mV and dissipates 79.2 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 36 at 250 MHz with self-resonance at 2800 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1608V1 family this is value 16 of 31, in a range from 1.6 to 470 nH.

    Where This Series Fits

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Why choose wire wound over multilayer?
    Q. A wound coil has lower resistance for the same inductance, so Q is higher and the loss in a filter or matching network is lower. The price is size and cost, which is why multilayer parts dominate pure decoupling.

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products