Eaton WCLA1608V1-680-R 68 nH Inductor, 600 mA Rated
Eaton WCLA1608V1-680-R 68 nH Inductor, 600 mA Rated

Eaton WCLA1608V1-680-R 68 nH Inductor, 600 mA Rated

Share
WCLA1608V1-680-R: wire wound chip inductor, 68 nH ±5%, Q 36 at 200 MHz, 600 mA rated, DCR 340 mOhm.
    • Product Details
    • Download

    Eaton WCLA1608V1-680-R 68 nH Inductor, 600 mA Rated

    WCLA1608V1-680-R at a glance: wire wound chip inductor, 68 nH ±5%, Q 36 at 200 MHz, 600 mA rated, DCR 340 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberWCLA1608V1-680-R
    OCL68 nH ±5%
    Q minimum @ test frequency36 @ 200 MHz
    SRF minimum1700 MHz
    DCR maximum @ +25 °C340 mOhm
    Rated current (20 °C rise)600 mA
    OCL test frequency200 MHz
    OCL test voltage500 mV
    Package1.78 x 1.10 mm, 0.95 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10982

    Outline Drawing

    WCLA1608V1-680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10982: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 600 mA rating the winding drops about 204 mV and dissipates 122 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 36 at 200 MHz with self-resonance at 1700 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1608V1 family this is value 21 of 31, in a range from 1.6 to 470 nH.

    What This Family Is For

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products