Eaton WCLA2012V1-222-R 2200 nH RF Chip Inductor, SRF 50 MHz
Eaton WCLA2012V1-222-R 2200 nH RF Chip Inductor, SRF 50 MHz

Eaton WCLA2012V1-222-R 2200 nH RF Chip Inductor, SRF 50 MHz

Share
WCLA2012V1-222-R: wire wound chip inductor, 2200 nH ±5%, Q 16 at 7.9 MHz, 150 mA rated, DCR 4200 mOhm.
    • Product Details
    • Download

    Eaton WCLA2012V1-222-R 2200 nH RF Chip Inductor, SRF 50 MHz

    WCLA2012V1-222-R at a glance: wire wound chip inductor, 2200 nH ±5%, Q 16 at 7.9 MHz, 150 mA rated, DCR 4200 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA2012V1-222-R
    OCL2200 nH ±5%
    Q minimum @ test frequency16 @ 7.9 MHz
    SRF minimum50 MHz
    DCR maximum @ +25 °C4200 mOhm
    Rated current (20 °C rise)150 mA
    OCL test frequency7.9 MHz
    OCL test voltage500 mV
    Package2.30 x 1.70 mm, 1.52 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10983

    Dimensions and Pad Layout

    WCLA2012V1-222-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10983: outline views
    with rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 150 mA rating the winding drops about 630 mV and dissipates 94.5 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 16 at 7.9 MHz with self-resonance at 50 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA2012V1 family this is value 36 of 36, in a range from 2.2 to 2200 nH.

    Positioning in the Range

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products