Eaton WCLA2012V1-470-R 47 nH RF Chip Inductor, SRF 1650 MHz
Eaton WCLA2012V1-470-R 47 nH RF Chip Inductor, SRF 1650 MHz

Eaton WCLA2012V1-470-R 47 nH RF Chip Inductor, SRF 1650 MHz

Share
WCLA2012V1-470-R: wire wound chip inductor, 47 nH ±5%, Q 55 at 500 MHz, 500 mA rated, DCR 310 mOhm.
    • Product Details
    • Download

    Eaton WCLA2012V1-470-R 47 nH RF Chip Inductor, SRF 1650 MHz

    WCLA2012V1-470-R at a glance: wire wound chip inductor, 47 nH ±5%, Q 55 at 500 MHz, 500 mA rated, DCR 310 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberWCLA2012V1-470-R
    OCL47 nH ±5%
    Q minimum @ test frequency55 @ 500 MHz
    SRF minimum1650 MHz
    DCR maximum @ +25 °C310 mOhm
    Rated current (20 °C rise)500 mA
    OCL test frequency200 MHz
    OCL test voltage500 mV
    Package2.30 x 1.70 mm, 1.52 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10983

    Dimensions and Pad Layout

    WCLA2012V1-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10983: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 500 mA rating the winding drops about 155 mV and dissipates 77.5 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 55 at 500 MHz with self-resonance at 1650 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA2012V1 family this is value 16 of 36, in a range from 2.2 to 2200 nH.

    What This Family Is For

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products