Eaton WCLA2012V1-681-R 680 nH Chip Inductor, Q 23
Eaton WCLA2012V1-681-R 680 nH Chip Inductor, Q 23

Eaton WCLA2012V1-681-R 680 nH Chip Inductor, Q 23

Share
WCLA2012V1-681-R: wire wound chip inductor, 680 nH ±5%, Q 23 at 50 MHz, 190 mA rated, DCR 2100 mOhm.
    • Product Details
    • Download

    Eaton WCLA2012V1-681-R 680 nH Chip Inductor, Q 23

    WCLA2012V1-681-R at a glance: wire wound chip inductor, 680 nH ±5%, Q 23 at 50 MHz, 190 mA rated, DCR 2100 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA2012V1-681-R
    OCL680 nH ±5%
    Q minimum @ test frequency23 @ 50 MHz
    SRF minimum300 MHz
    DCR maximum @ +25 °C2100 mOhm
    Rated current (20 °C rise)190 mA
    OCL test frequency25 MHz
    OCL test voltage500 mV
    Package2.30 x 1.70 mm, 1.52 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10983

    Outline Drawing

    WCLA2012V1-681-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10983: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    Ceramic-core wire wound parts hold their value well with DC bias because there is no magnetic material to saturate. Ferrite-core versions give more inductance per size but start to roll off as the bias current rises.

    At the 190 mA rating the winding drops about 399 mV and dissipates 75.8 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 23 at 50 MHz with self-resonance at 300 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA2012V1 family this is value 30 of 36, in a range from 2.2 to 2200 nH.

    Where This Series Fits

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products