Eaton WCLA2520V1-1R0-R 1 uH Inductor, 1000 mA Rated
Eaton WCLA2520V1-1R0-R 1 uH Inductor, 1000 mA Rated

Eaton WCLA2520V1-1R0-R 1 uH Inductor, 1000 mA Rated

Share
WCLA2520V1-1R0-R: wire wound chip inductor, 1 uH ±10%, Q 12 at 7.96 MHz, 1000 mA rated, DCR 130 mOhm.
    • Product Details
    • Download

    Eaton WCLA2520V1-1R0-R 1 uH Inductor, 1000 mA Rated

    WCLA2520V1-1R0-R at a glance: wire wound chip inductor, 1 uH ±10%, Q 12 at 7.96 MHz, 1000 mA rated, DCR 130 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberWCLA2520V1-1R0-R
    OCL1 uH ±10%
    Q minimum @ test frequency12 @ 7.96 MHz
    SRF minimum345 MHz
    DCR maximum @ +25 °C130 mOhm
    Rated current (20 °C rise)1000 mA
    OCL test frequency7.96 MHz
    OCL test voltage500 mV
    Package2.90 x 2.50 mm, 2.10 mm high
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1152

    Mechanical Dimensions & Pad Layout

    WCLA2520V1-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1152: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 1000 mA rating the winding drops about 130 mV and dissipates 130 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 12 at 7.96 MHz with self-resonance at 345 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA2520V1 family this is value 2 of 13, in a range from 0.22 to 47 uH.

    Series Positioning

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Is the automotive version electrically different?
    The construction is the same; the qualification and the temperature range are not. The WCLA parts are AEC-Q200 qualified and rated to +125 °C, the commercial WCL parts to +85 °C.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products